Set Your 1991 Honda CRX Catalog
A down arrow

Skunk2 Alpha Series Throttle Body for 1991 Honda CRX

General Representation
General Image (Actual Part May Vary)
Fits:
Honda CRX - 1988 to 1991 - Coupe [All Trim Levels]
Notes:
66mm
More Info:
Requires the use of a Skunk2 Pro Series Intake Manifold or similar. May require tuning due to the increase in airflow.
List Price:
$138.59
Our Price:
$123.97
You Save:
$14.62
 
 
(shipping rates shown in cart)
Select an Application For Your
1991 Honda CRX
 
Door Config  [Trim Level]
Application / Notes
Coupe [All]
(66mm)
Coupe [All]
(70mm)
 
🔰 Honda CRX Fitment Help
Quicker Navigation & Better Info
Set Your Car Once & Site Customizes For It

CARB Compliance / Exemption Warning: If you live in California and your application for this product is not CARB Compliant / Exempt, then you cannot purchase it for public highway or street use (in that case it could only be used for formally sanctioned race use on a racing vehicle that may never be used on a public highway or street). If your application is not CARB Compliant / Exempt and you're shipping to California, our system will let you know on the final checkout page.

IMPORTANT FITMENT INFO FOR B/D/F/H SERIES ENGINES: If you are using this product on a B/D/F/H Series engine, then you must have a manual transmission and it is recommended you use a Skunk2 Pro Series Intake Manifold or make adjustments to your current intake manifold throttle body flange to match the bore diameter and keep the IAC (Idle Air Control) passage separate.

The Skunk2 Alpha Series Throttle Bodies are a solid entry level upgrade for your induction system. These throttle bodies are made from precision die-cast aluminum and are fine shot blasted for a quality finish. The throttle plate is precision machined brass with sealed ball bearing for smooth operation. Since this is designed to be a direct bolt on, it is compatible with the stock cables and coolant lines.The perfect solution for those looking to add a bit more power to their build.

Key Features:
  • Increases horsepower and torque by optimizing airflow to your engine.
  • Gains of up to 10+ hp, naturally aspirated (more on turbocharged and supercharged vehicles).
  • Hardware and a NEW THERMAL THROTTLE BODY GASKET are included when applicable (factory O-rings can be re-used).
  • Available in two different sizes.
  • Made of precision die-cast aluminum. Very durable and allows Skunk2 to price this throttle body well below the traditional "Pro Series" one.
  • Great reliability and smooth operation - exceeds industry standards.
  • Great when paired with a cold air intake!
Tuning Info: Since this throttle body allows more airflow than your stock throttle body, ADJUSTING THE ECU CALIBRATION AFTER INSTALLING THIS PART IS USUALLY REQUIRED. Otherwise, your car may not drive correctly or get full power.

TPS Sensor Notes: If you think your stock Throttle Position Sensor (TPS) is getting old or is not working correctly, we recommend getting a new TPS sensor to avoid power loss, bogging, and other problems associated with old TPS sensors.

  Don't have a 1991 Honda CRX?

Application Price List & Information Overview
Application List Price Our Price
Honda CRX - 1988 to 1991 - Coupe [All] Skunk2 Alpha Series Throttle Body

Notes: (66mm)

More Info: Requires the use of a Skunk2 Pro Series Intake Manifold or similar. May require tuning due to the increase in airflow.
$138.59$123.97
Honda CRX - 1988 to 1991 - Coupe [All] Skunk2 Alpha Series Throttle Body

Notes: (70mm)

More Info: Requires the use of a Skunk2 Pro Series Intake Manifold or similar. May require tuning due to the increase in airflow.
$138.59$123.97
Featured Supported Door Configuration:
Honda CRX Coupe

Skunk2 Alpha Series Throttle Body supported 1991 Honda CRX Trim Levels:
DX , HF , Si


Our Customers Love Us - See our Reviews
...Loading Reviews